Best Camera Mounts: 10 Picks for Rigs, Monitors, and Action Cameras in 2026

The best camera mounts depend on what you need to attach and where you need to position it, from a field monitor on a cage to an action camera on a handlebar. These ten picks cover clamps, articulated arms, monitor holders, and a tabletop stand; check the attachment standard, supported load, and mounting surface before choosing.

Quick Top Products

Handlebar-Ready Action Camera Clamp

SMALLRIG Camera Mount Clamp, Gopro Motorcycle and Bike Handlebar Mount Kit

This SmallRig clamp is built for mounting an action camera or other accessory to a round bar or flat edge. Its jaw accommodates rods from 14 mm and surfaces up to 65 mm thick, while a 360° ball head helps set portrait or landscape framing.

A removable action-camera adapter is included, and 1/4"-20 and 3/8"-16 threaded holes provide other attachment options. The stated 7.7 lb maximum applies at rest; for motion, the notes limit device weight to 0.77 lb, advise avoiding rough terrain, and give a speed limit.

Those motion restrictions are central to deciding whether it fits a moving-camera setup.

Best For: Action-camera users who want a ball-head clamp for a handlebar, table, or tripod.

Choose this clamp for an action camera that needs to move between a bike handlebar, table, or tripod. Its adapter and rotating head give it a broader role than a fixed mount, but the motion guidance is much more restrictive than its at-rest load figure.

Check the bar or edge diameter, adapter fit, and camera weight for the way you plan to use it. For a stationary camera accessory, compare the load limit and jaw range with the other clamp options.

Check Price on Amazon

Friction-Grip Table Clamp Kit

SMALLRIG Magic Arm Clamp Kit, Camera Mount Friction Arm with Super Clamp

This kit combines a super clamp and magic arm for placing a small camera, monitor, light, webcam, action camera, or microphone beside a work surface or rig. A rotating triangular prism friction block is designed to improve grip on flat surfaces, while the clamp can also grasp round tubes.

The arm adjusts with one knob, and its recommended load capacity is 1.5 kg. Cushions at the clamp and arm contact points add friction and help protect the clamped area.

It suits flexible tabletop framing, but buyers should make sure the surface and the attached device fall within the intended grip and load conditions.

Best For: Creators positioning a small camera or accessory at a desk or on a round tube.

This is a useful fit when a table edge or tube is the mounting point and the camera needs a little reach from the clamp. The friction block and cushions suit surface contact, while the single knob simplifies angle changes.

Its 1.5 kg recommendation makes the attached load an important check, especially with a monitor or camera. Check the arm length and thread standards if those details matter to your setup.

Check Price on Amazon

Compact Dual-Ball Super Clamp

SmallRig Cool Ballhead Arm Super Camera Clamp Mount Double Ball Adapter, Fence Desk Table Mount for Ronin-M for Insta360, for Gopro - 1138

SmallRig's 1138 pairs a super clamp with a double-ball adapter and an action-camera mount. The 1/4"-20 screw accepts cameras, webcams, monitors, lights, microphones, and other gear; the clamp locks to a rod, tube, table, frame, or tripod without drilling.

It has a maximum supported load of 1.5 kg and is made from aluminum and stainless steel. For dynamic use, the notes advise attaching a safety rope to prevent accidental drops.

This is a practical choice for compact accessory positioning, provided the mounting surface and attached gear suit the clamp and load limit.

Best For: Small camera and accessory rigs needing a compact clamp with a 1/4"-20 connection.

Pick the 1138 when a compact clamp and 1/4"-20 mount cover the setup, and the included action-camera adapter is useful. It supports a range of surfaces, but the 1.5 kg ceiling and safety-rope advice matter for gear that may move or be bumped.

Check the clamp's fit on the intended rod or edge and account for the complete accessory load. A dedicated monitor holder may provide a more direct fit if monitor positioning is the only task.

Check Price on Amazon

Long-Reach Arm and Super Clamp Kit

SMALLRIG 9.8 Inches Magic Arm Clamp Kit with 1/4" and 3/8" Threaded Holes

This kit brings together a 9.8-inch articulating arm and a super clamp with 1/4" and 3/8" threads. The clamp opens from 15 mm to a maximum of 54 mm, while ball-head joints provide 360° adjustment for accessories such as a monitor, microphone, or light.

Both the clamp and arm have rubber cushions to help protect contact surfaces and hold accessories more securely. The arm's two ends use 1/4" screws.

It is a flexible rigging option when you need distance from the clamping point, but the notes do not give a load rating, so confirm the intended equipment weight before relying on the extended arm.

Best For: Camera operators who want a specified arm length and 1/4" or 3/8" clamp threads.

Choose this kit when its 9.8-inch reach and both clamp thread sizes suit the rig. It gives more reach and thread flexibility than a standalone super clamp, but no maximum load is supplied, so check before mounting heavier equipment.

Its clamp opening range also matters: confirm the bar or edge falls within it. The notes specifically rule out seawater use, making this a poor fit for that environment.

Check Price on Amazon

11-Inch Anti-Twist Arm

SMALLRIG 11" Magic Arm Clamp with 1/4"-20 Screw & Retractable Pins

The 5311 combines an 11-inch magic arm with a crab-shaped clamp. Its accessory end uses a 1/4"-20 screw and retractable pins, with a knurled thumbscrew for tool-free fastening and an Allen-wrench hole for extra tightening.

The clamp fits tubes, tables, tripod legs, and stabilizer rings from 15 to 40 mm in diameter. Its maximum payload is 1.5 kg, and the notes describe anti-slip pads and an anti-twist connection.

This longer arm suits setups where a direct clamp position is awkward, though its reach and load should be checked against the exact camera and accessory combination.

Best For: Vloggers and streamers mounting an action camera, light, microphone, or monitor to a tube or table.

This is a good match when an 11-inch arm helps move an accessory away from a clamp point and the retractable pins suit its mounting interface. The 15 to 40 mm clamp range limits where it can attach, and the 1.5 kg payload sets the load ceiling.

Check both the surface diameter and the complete accessory weight. The adjustable joints let you position the arm for vlogging, live streaming, or studio filming.

Check Price on Amazon

Compact 7-Inch Anti-Twist Arm

SMALLRIG 7 Inches Magic Arm Clamp, with 1/4 Screw & Anti-Deflection Pin

The 5310 pairs a 7-inch magic arm with a crab-shaped clamp for positioning an action camera, monitor, light, microphone, or similar accessory. Its 1/4"-20 screw and retractable pins connect at the accessory end, while the thumbscrew enables tool-free adjustment and the included Allen wrench offers extra tightening.

The clamp fits tubes, tables, tripod legs, or stabilizer rings between 15 and 40 mm in diameter. Maximum payload is 1.5 kg.

The shorter arm can keep an accessory closer to the mounting point than longer arms, which may suit a tighter rig; confirm that its reach and clamp diameter cover the setup.

Best For: Compact camera rigs needing a shorter arm with retractable anti-twist pins.

Pick this shorter version when the camera accessory should sit closer to the clamp or the rig has limited space. It has a 15 to 40 mm clamp range and a 1.5 kg maximum payload, so check the mounting diameter and accessory load.

Consider whether the retractable pins match the cage or device. The ball joints can be positioned and locked with the wing nut.

Check Price on Amazon

Wide-Jaw Action Camera Clamp

SMALLRIG Super Clamp Mount, Ballhead Magic Arm and Adapter for Gopro

This super clamp includes a removable GoPro adapter and offers 1/4"-20 and 3/8"-16 threaded holes for cameras, monitors, lights, DSLRs, or microphones. Its jaw accepts rods from 14 to 60 mm and surfaces up to 65 mm thick, giving it a broad choice of mounting points.

The product has a 3.5 kg maximum load capacity, and its ball heads adjust through 360°. Built-in cushions and a hex-hole fastening design address grip and anti-twist positioning.

Check whether the included action-camera adapter fits your camera cage, and consider how securely the clamp can sit on the chosen surface.

Best For: Action-camera and small-rig users who need a broad jaw range and a removable adapter.

Choose this clamp when the wide jaw range or 3.5 kg maximum load suits the setup, and the GoPro adapter is useful. Its 14 to 60 mm rod range and 65 mm surface thickness limit are worth checking against the attachment point.

The load figure does not distinguish moving from stationary use, so confirm suitability for any setup that will travel or vibrate. Check whether the clamp's threaded holes and adapter fit your accessories.

Check Price on Amazon

Cold-Shoe Monitor Mount with Portrait Support

SMALLRIG Camera Monitor Mount with Cold Shoe, 180° Tilt and 360° Swivel, Retractable 1/4" Locating Screw Anti-Twist, Damping Adjust, Horizontal & Vertical Shooting

The 6313 is a monitor mount that slides into a cold shoe or hot shoe and locks in place, with a 1/4"-20 threaded hole at the base for other accessories. Its retractable locating screw, locating pins, and silicone pad are designed to resist twisting and scratching at the monitor interface.

The mount supports horizontal and vertical installations, tilts 180°, and pans 360°; tilt damping adjusts by thumb knob. An L-shaped Allen wrench is included for additional tightening.

This is a direct fit for a shoe-based video rig, but verify that the monitor's screw interface and cage shoe are compatible.

Best For: Video creators who want a quick-lock monitor mount that can switch between landscape and portrait.

Choose this model when a cold-shoe base is the simplest way to mount a monitor and portrait orientation matters. Its 1/4"-20 base thread adds another rigging option, while the locating features address rotation at the monitor connection.

Confirm the shoe and monitor interfaces before buying. Not specified: load limit.

Check that the mount supports your monitor's weight and that its locating pins fit the monitor.

Check Price on Amazon

ARRI Locating Mount for Larger Monitors

SMALLRIG Monitor Mount EVF Holder Support with Locating Pins for ARRI Standard - 2174

The 2174 holds a 5-inch or 7-inch monitor and connects to a cage or handle through a 3/8" threaded hole for ARRI standard. It supports monitors up to 1.5 kg and allows up to 146° of rotation adjustment with one hand.

A thumbscrew provides toolless installation and quick release, with an Allen-wrench hole available for retightening. If a cage lacks ARRI locating holes, the notes say an optional Mini Plate 2171 can attach through two 1/4" threaded holes.

Check the cage interface and monitor size; this mount is aimed at rigs with the matching locating standard.

Best For: Operators attaching a 5-inch or 7-inch monitor to an ARRI locating hole on a cage or handle.

This is the clearest choice here for a monitor rig already built around ARRI locating holes. It supports 5-inch and 7-inch monitors up to 1.5 kg, and the hand-adjustable rotation avoids a tool for routine positioning.

Check the cage or handle interface first; rigs without locating holes need the optional plate described in the notes. A cold-shoe mount is more straightforward if your camera rig already has a shoe and you do not need the ARRI connection.

Check Price on Amazon

Height-Adjustable Desktop Camera Stand

SMALLRIG Camera Mount C Stand, 15"-35" Adjustable Desk Clamp Table Tripod

This tabletop camera stand uses a C-clamp and three extending pole sections to position a camera, ring light, or smartphone for desk-based shooting. Its notes give an adjustment range of 19 to 39 inches with the ball head and clamp, and say the clamp suits tables up to 1.85 inches thick.

A 1/4" ball head turns 360° and tilts from -90° to +45°; maximum load is 6.6 lb. The ball head can be detached for another device with a 1/4"-20 threaded hole.

It offers more height than small articulated arms, but requires a desk edge within the clamp's thickness range.

Best For: Desk-based livestreaming, interviews, beauty shoots, or overhead camera and light positioning.

Choose this stand for a desk-based setup that benefits from pole height rather than a short arm. Its three sections, adjustable ball head, and ring-light adapter make it useful for livestreams and interviews, while the table thickness and 6.6 lb load set practical boundaries.

Measure the desk edge and account for the complete camera or light assembly. For a compact mounting point on a tube or edge, one of the small clamp arms may be easier to position.

Check Price on Amazon

How to Choose Camera Mounts

How We Picked Camera Mounts

This selection focuses on complete supports that attach a camera or common filming accessory to a rig, desk, bar, or cage. We included clamp kits with articulated arms, action-camera adapters, a height-adjustable tabletop stand, and monitor holders because each addresses a distinct mounting task.

Fit and interface were key criteria. The products cover 1/4"-20 screws, 3/8" threads, cold shoes, ARRI locating holes, clamp jaws, and specific monitor or action-camera connections.

We also favored records that made a load limit, jaw range, or mounting surface clear enough to guide a practical choice.

Comparing Camera Mounts for Rigs and Surfaces

A clamp and arm can reposition a camera accessory away from a table edge, tube, tripod leg, or rig. The 9.8-inch kit provides a stated arm length and 1/4" and 3/8" clamp threads, while the 5311 and 5310 have retractable pins, a 15 to 40 mm clamp range, and a 1.5 kg payload.

Choose arm length around available space and required reach, then check the clamp's fit and the mounted load.

The action-camera clamps differ in adapter, jaw range, and movement guidance. The 4102B includes a removable adapter and specific limits for moving use.

The wider-jaw GoPro clamp accepts rods from 14 to 60 mm and has a 3.5 kg maximum load, but gives no separate moving-use limit. The 1138 is a compact 1.5 kg option with a safety-rope recommendation for dynamic use.

A maximum load figure should be read with any stated conditions attached.

Monitor mounts depend heavily on the camera cage interface. The 6313 uses a cold or hot shoe and adds portrait positioning; the 2174 attaches through an ARRI locating connection and specifies support for 5-inch or 7-inch monitors up to 1.5 kg.

Verify both ends of the connection before buying, including whether a cage needs an additional plate.

Choosing a Camera Mount for Desk or Table Use

For a fixed desk setup, the 15–35-inch stand offers pole height, a 360° ball head, and a clamp designed for table edges up to 1.85 inches thick. It suits a camera or ring light positioned above a workspace, interview setup, or livestream area.

Check that the desk edge is accessible and falls within the clamp limit.

Smaller clamp arms take less space and can mount to a table edge or round tube, but they provide less height than the stand. A rotating friction block may help with a flat edge, while padded jaws help grip and protect a surface.

Before attaching a device, confirm the clamp opening, arm position, and load capacity together.

Which Camera Mount Fits Your Setup?

For moving action-camera use, start with the 4102B and follow its motion-specific weight, terrain, and speed limits. For a broad jaw range with a GoPro adapter, consider the B0B5LFC6L3 clamp and check how its load rating applies to your use.

For a monitor on a shoe, the 6313 provides horizontal and vertical positioning; for a cage with ARRI locating holes, the 2174 gives a defined monitor size and load range. Choose the tabletop stand for desk height and a ring-light option.

For compact rigging reach, compare the 7-inch and 11-inch arms against the space available and the weight of the attached gear.