Product Reviews

Donner DP-1 Guitar Power Supply Review

A compact option for guitarists who need several pedal outputs and use a mix of 9V, 12V, and 18V effects.

This article contains affiliate links. We may earn a commission if you buy through them, at no extra cost to you.

The Donner DP-1 Guitar Power Supply review centers on a compact supply for players who want to power several effects from one pedalboard unit.

Its ten outputs cover common 9V needs plus a 12V and an 18V option, with current limits that make checking each pedal’s requirements essential.

Donner DP-1 Review Summary

The quick verdict

Donner DP-1 Guitar Power Supply
4.5/5

7,000+ ratings

Read Amazon Reviews

Donner DP-1 Guitar Power Supply

A compact option for guitarists who need several pedal outputs and use a mix of 9V, 12V, and 18V effects.

  • Ten outputs: seven 9V/100mA, one 9V/500mA, one 12V/100mA, and one 18V/100mA.
  • AC input range of 100V–240V, with an 18V DC supply input.
  • Independent short-circuit protection for each output.
  • Circuit design intended to provide an isolation effect; the manufacturer notes it is not absolute isolation.

Pros

  • Offers ten outputs across three voltage options.
  • Includes one 9V output rated at 500mA for a compatible pedal with a higher current requirement.

Consider before buying

  • Nine of the ten outputs are rated at only 100mA, so the output count alone does not guarantee compatibility with every pedal.
  • The isolation design is not described as absolute circuit isolation, which may matter to buyers comparing power-supply designs.
Read the full review summary

The DP-1 combines seven 9V outputs rated at 100mA each with one 9V output rated at 500mA, one 12V/100mA output, and one 18V/100mA output.

That mix can suit a board with multiple lower-current pedals and a specific need for a higher-current 9V connection or a different voltage.

It includes ten power cables, a lightweight aluminum-alloy enclosure, a blue LED, and independent short-circuit protection for each output.

Donner describes the outputs as isolated through circuit simulation and design, while clarifying that the circuit is not absolutely isolated.

Buyers should compare their pedals’ voltage, polarity, connector, and current requirements with the supply and cable details before choosing it.

The buying factors

Donner DP-1 Scorecard

Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.

8/10

Output variety

Ten outputs span 9V, 12V, and 18V, including two different 9V current ratings.

6/10

Current flexibility

The 500mA 9V output adds flexibility, while the other nine outputs are each rated at 100mA.

8/10

Board capacity

Ten listed outputs can cover a multi-pedal setup, provided each pedal fits an output’s electrical limits.

8/10

Output protection

Independent short-circuit protection is specified, so one affected output need not stop the others from working.

5/10

Isolation clarity

The design aims to provide an isolation effect, but the product notes explicitly say it is not absolute circuit isolation.

8/10

Portability

The aluminum-alloy construction and listed item weight of 6.9 ounces point to an easy-to-carry form.

Key Features and Specifications of Donner DP-1

  • Ten outputs: seven 9V/100mA, one 9V/500mA, one 12V/100mA, and one 18V/100mA.
  • AC input range of 100V–240V, with an 18V DC supply input.
  • Independent short-circuit protection for each output.
  • Circuit design intended to provide an isolation effect; the manufacturer notes it is not absolute isolation.
  • Aluminum-alloy enclosure, compact rectangular form, and listed weight of 6.9 ounces.
  • Blue LED indicator and ten included power cables.

Pros and Cons of Donner DP-1

Pros

  • Offers ten outputs across three voltage options.
  • Includes one 9V output rated at 500mA for a compatible pedal with a higher current requirement.
  • Independent short-circuit protection lets other outputs continue operating if one output is short-circuited.
  • Lightweight metal enclosure and included cables make it a ready-to-configure pedalboard option.

Consider before buying

  • Nine of the ten outputs are rated at only 100mA, so the output count alone does not guarantee compatibility with every pedal.
  • The isolation design is not described as absolute circuit isolation, which may matter to buyers comparing power-supply designs.
  • The 12V and 18V outputs are each limited to 100mA, so verify both voltage and current needs before assigning a pedal.

Who Should Buy Donner DP-1?

Good fit

Consider the DP-1 if your board has several effects with compatible barrel connections and their power needs fit the listed outputs.

The seven 9V/100mA sockets can handle multiple pedals that fall within that rating, while the separate 9V/500mA output provides another option for a compatible higher-current effect.

Its 12V and 18V outputs can be useful when your setup includes a pedal designed for one of those voltages and no more than 100mA.

The 100V–240V AC input range also suits a range of mains input voltages; confirm the correct plug and any regional requirements for your setup.

Before buying, make a list of each pedal’s required voltage, polarity, connector type, and current draw, then match it to an individual output.

Leave headroom where possible, and check the supplied cable ends against your pedals and board layout.

Who should skip it

Skip this option if your pedals’ current demands exceed the available output ratings or if your board needs more than one 9V output rated at 500mA.

Check the power requirements for digital, high-draw, or unusual pedals individually rather than assuming every effect will work from a standard 9V connection.

If your decision depends on absolute circuit isolation, this design’s stated limitation may make it a poor fit. Compare the electrical design details of alternatives and confirm what type of isolation your setup requires.

How the Donner DP-1 Fits a Pedalboard

Match outputs to pedal requirements

The DP-1’s ten-output count is useful only when each effect matches its assigned socket. Most of its outputs are 9V/100mA, so check individual current draw rather than treating the total output count as a promise of broad compatibility.

The single 9V/500mA socket gives one higher-current choice, but it does not change the ratings of the remaining outputs.

Use voltage options carefully

The dedicated 12V and 18V outputs give the board options beyond 9V, but each is rated at 100mA. Use them only for pedals designed for the corresponding voltage, and verify current draw and polarity as well.

A higher voltage is not a general upgrade; the pedal’s own requirements should determine which connection is suitable.

Understand the isolation wording

Donner describes a circuit-simulation and design approach intended to achieve an isolation effect, then qualifies that the circuit is not absolutely isolated.

The independent short-circuit protection is a separate practical feature: the product specifies that other outputs can continue working if one output is short-circuited. Buyers sensitive to noise or isolation should weigh those points separately.

Plan the physical setup

The supply has a lightweight aluminum-alloy enclosure, a blue LED, and ten included power cables.

Those details support a compact pedalboard setup, but the available description does not give a reliable footprint measurement because its listed dimensions appear inconsistent.

Check the physical space and cable reach against your board before settling on a mounting position.

Alternatives to Donner DP-1

No competing power supply is recommended here. Compare output voltage, current, protection, and isolation design when evaluating another model.

Guitar & Bass Accessories alternative

Donner Pedalboard Pedal Tape
4.7/5

1,000+ ratings

Read Amazon Reviews

Donner Pedalboard Pedal Tape

Choose the DP-1 when you need a multi-output pedal power supply. The tape addresses pedal mounting rather than power, so it is relevant only if securing effects to a board is your separate need.

  • This product is hook-and-loop mounting tape: a 2m-long, 50mm-wide strip with adhesive backing that can be cut to length for attaching pedals to a pedalboard.
  • The DP-1 supplies power to compatible effects through ten outputs with several voltage and current ratings.

Is Donner DP-1 Worth It?

The Donner DP-1 is worth considering for a pedalboard with several effects whose electrical needs fit its ten specified outputs.

Its mix of 9V, 12V, and 18V connections, the 9V/500mA option, and independent short-circuit protection are useful design features.

Buy it after checking each pedal’s voltage, polarity, connector, and current draw against the individual outputs. If your setup needs higher current on multiple outputs or depends on absolute isolation, compare other supply designs before deciding.

Your review at a glance

Donner DP-1 Guitar Power Supply
4.5/5

7,000+ ratings

Read Amazon Reviews

Donner DP-1 Guitar Power Supply

A compact option for guitarists who need several pedal outputs and use a mix of 9V, 12V, and 18V effects.

  • Ten outputs: seven 9V/100mA, one 9V/500mA, one 12V/100mA, and one 18V/100mA.
  • AC input range of 100V–240V, with an 18V DC supply input.
  • Independent short-circuit protection for each output.
  • Circuit design intended to provide an isolation effect; the manufacturer notes it is not absolute isolation.

Written by

latalklive.com Editorial Team

Editorial team

Independent editorial coverage of talk, audio & culture.

Amazon customer reviews

See what buyers think

Explore customer reviews, photos and available video reviews on Amazon.

Donner DP-1 Guitar Power Supply

Donner DP-1 Guitar Power Supply

A compact option for guitarists who need several pedal outputs and use a mix of 9V, 12V, and 18V effects.

  • Ten outputs: seven 9V/100mA, one 9V/500mA, one 12V/100mA, and one 18V/100mA.
  • AC input range of 100V–240V, with an 18V DC supply input.
Check Video Reviews on Amazon